Home › Math & Science › Resistor Calculator

Resistor Calculator

A resistor pulled from a parts bin carries no printed label — its value is painted on as colored bands, and those bands mean nothing until you decode them. This free resistor calculator does all three jobs: it turns 4-band, 5-band and 6-band color codes into a resistance in ohms, it works backwards from a value to the exact bands you should look for, and it combines resistors in series or parallel so an odd value you do not own can be built from ones you do.

1 · Color code → resistance

—
2 · Resistance value → band colors

—
3 · Series & parallel combiner

—

How it works

A through-hole resistor is too small for printed numbers, so its value is encoded as colored bands read in order. The first bands are significant digits, the band after them is a multiplier — a power of ten the digits are multiplied by — and the last band before any extra spacing is the tolerance, the percentage the real value may sit above or below the marked one. On a 6-band part, one final band gives the temperature coefficient: how many parts per million the resistance drifts for each kelvin (degree) of temperature change.

Resistance (Ω) = (digit₁ digit₂ [digit₃]) × multiplier  ·  Tolerance range = value × (1 ± tolerance %)  ·  Series: R = R₁ + R₂ + …  ·  Parallel: 1/R = 1/R₁ + 1/R₂ + …

Each color stands for a fixed digit, and most colors keep the same meaning everywhere in the code: black is 0, brown 1, red 2, and so on up to white at 9. Read as a multiplier, a color means 10 raised to that digit — red means ×100 — with two exceptions: gold multiplies by 0.1 and silver by 0.01, which is how values under 10 Ω are expressed. As a tolerance band, gold means ±5% and silver ±10%; a resistor with only three bands and no tolerance band is a ±20% part. The chart below is the full code this calculator uses.

ColorDigitMultiplierToleranceTemp. coefficient
Black0×1—250 ppm/K
Brown1×10±1%100 ppm/K
Red2×100±2%50 ppm/K
Orange3×1,000±3%15 ppm/K
Yellow4×10,000—25 ppm/K
Green5×100,000±0.5%—
Blue6×1,000,000±0.25%10 ppm/K
Violet7×10,000,000±0.1%5 ppm/K
Gray8×100,000,000±0.05%1 ppm/K
White9×1,000,000,000——
Gold—×0.1±5%—
Silver—×0.01±10%—
No band——±20%—

Series and parallel combinations cover the gaps in your parts drawer. Wiring resistors in series — one after another in a single chain — simply adds their values, and each one drops part of the voltage. Wiring them in parallel — all legs connected across the same two points — adds the reciprocals instead, so the total always lands below the smallest resistor in the group, while the current splits between the branches.

Worked example

A common 4-band resistor is marked yellow, violet, red, gold. Step 1: read the digit bands — yellow is 4 and violet is 7, giving the two digits 47. Step 2: apply the multiplier band — red means ×100, so 47 × 100 = 4,700 Ω, or 4.7 kΩ. Step 3: apply the tolerance band — gold means ±5%, and 5% of 4,700 is 235, so the real value sits between 4,700 − 235 = 4,465 Ω and 4,700 + 235 = 4,935 Ω. Those are this calculator's default bands in section 1, and 4.7 kΩ with a 4,465–4,935 Ω range is exactly what it shows.

Tips and common mistakes

Reading direction is the classic trap: the value bands are grouped together and the tolerance band sits slightly apart, often in gold or silver, so always start from the grouped end. Heat and age fade paint — orange starts to look like red, and brown and black blur together — so on a band that decides the answer, confirm with a multimeter before soldering the part into a circuit. Precision parts hide a second trap: a 5-band 1 kΩ resistor (brown, black, black, brown, brown) read as a 4-band part looks like 10 Ω with a stray band, so when a decoded value makes no sense for the circuit, count the bands again. And when you combine resistors in parallel to hit an exact value, remember the pair also splits the load — two half-watt resistors in parallel or series can safely handle more power together than either one alone, as long as they are equal values sharing the load evenly.

FAQ

How do I read a resistor color code?

Start at the end opposite the tolerance band — the gold, silver or extra-spaced band goes last. The first two bands (three on 5-band and 6-band parts) are significant digits, the next band is the multiplier, and the final band is the tolerance. Yellow, violet, red and gold, for example, means digits 4 and 7, multiplied by 100, with ±5% tolerance: 4,700 Ω.

What do the gold and silver bands mean?

Gold and silver never appear as digit bands. In the multiplier position, gold means multiply by 0.1 and silver means multiply by 0.01, which is how values below 10 Ω are written. In the tolerance position, gold means ±5% and silver means ±10%. A resistor with no tolerance band at all is rated ±20%.

Which end of the resistor do I start reading from?

Read from the end farthest from the tolerance band. The tolerance band is usually gold or silver, and it often sits a little apart from the group of value bands, so the tightly grouped bands come first. If a part still looks the same from both ends, remember the first band is never gold or silver — and a multimeter reading settles any doubt in seconds.

What is the difference between 4-band, 5-band and 6-band resistors?

A 5-band resistor has three significant digits instead of two, so it can state values more precisely — 1.00 kΩ rather than 1 kΩ — and it usually carries a tighter tolerance, often ±1% or better. A 4-band part is the everyday ±5% or ±20% type. A 6-band resistor adds one more band after the tolerance band that gives the temperature coefficient in parts per million per kelvin, which matters in precision circuits.

How do resistors add up in series and parallel?

In series, the values simply add: 100 Ω + 100 Ω = 200 Ω. In parallel, the reciprocals add instead, so the total is always less than the smallest single resistor: 100 Ω in parallel with 100 Ω is 1 ÷ (1/100 + 1/100) = 50 Ω. Two equal resistors in parallel always give exactly half of one resistor's value, a handy trick for building an odd value or sharing power between two parts.

Disclaimer: Results are the nominal values the color code represents. A real resistor's measured value depends on its tolerance, temperature and age — verify critical parts with a multimeter before use, and observe safe working practices with live circuits.