Home › Math & Science › Ohms Law Calculator

Ohms Law Calculator

You know the battery is 12 volts and the resistor is marked 4 ohms — but how much current will flow, and how much power will the resistor have to handle? This free ohms law calculator answers both questions from any two values you have: fill in any two of voltage, current, resistance and power, and it works out the other two.

Fill in any two boxes and clear the ones you don't know. Example: 12 V and 4 Ω gives 3 A and 36 W.

Current = 3 A · Power = 36 W
Solved from voltage and resistance — all four values shown below.
Voltage (V)12 V
Current (I)3 A
Resistance (R)4 Ω
Power (P)36 W

How it works

Ohm's law ties three quantities together: the voltage pushing electricity through a component, the current that flows, and the resistance opposing it. The power formula adds the fourth — how much electrical energy per second turns into heat, light or motion. Because the four are locked together, any two of them determine the other two, which is exactly what this calculator exploits.

V = I × R   •   I = V ÷ R   •   R = V ÷ I   •   P = V × I   •   P = I² × R   •   P = V² ÷ R

Voltage (V), in volts, is the electrical pressure — a car battery provides about 12 V, a US wall outlet about 120 V. Current (I), in amps, is how much charge flows per second. Resistance (R), in ohms, is how strongly the component resists that flow — a small heater element might be 10–20 Ω, a long thin wire a fraction of an ohm. Power (P), in watts, is the rate of energy use, and it is what melts fuses and sizes resistors: a resistor must be rated for at least the wattage the calculator shows, with margin to spare.

Depending on which pair you enter, the calculator reaches the answer by a different route. From voltage and resistance it divides, I = V ÷ R, then multiplies for power. From resistance and power it goes through square roots, V = √(P × R) and I = √(P ÷ R). Every route is shown in the formula line above, and all four results always agree with each other and with V = I × R — if you enter three or four values that contradict each other, the calculator solves from the first complete pair (voltage first, then current) so the answer set stays consistent.

Worked example

A 12-volt car battery is connected across a 4-ohm resistor. How much current flows, and how much power does the resistor dissipate?

Step 1 — current: I = V ÷ R = 12 ÷ 4 = 3 amps.
Step 2 — power: P = V × I = 12 × 3 = 36 watts.
Step 3 — check with the third form: P = V² ÷ R = 144 ÷ 4 = 36 W. Same answer, as it must be.

Enter 12 in the voltage box and 4 in the resistance box above, leave the other two empty, and you get exactly this: 3 A of current and 36 W of power — so in a real build you would reach for a resistor rated well above 36 W, or several resistors sharing the load.

Common mistakes

Entering three values that don't agree. If you type a voltage, a current and a resistance that don't satisfy V = I × R, no answer can honour all three. The calculator solves from the first complete pair and recomputes the rest — check the results table to see the consistent set.

Expecting Ohm's law to describe an LED or a motor. Ohm's law is exact for resistors. An LED drops a nearly fixed voltage however much current flows (within limits), so "its resistance" changes with operating point; a spinning motor generates back-voltage. The formulas still give a rough estimate, but not a design value.

Forgetting the power rating. Getting the resistance right is only half the job. A 4 Ω resistor carrying 36 W gets hot fast; small hobby resistors are often rated at ¼ W. Always compare the calculated power with the component's rating.

FAQ

What is Ohm's law?

Ohm's law says the voltage across a resistor equals the current through it times its resistance: V = I × R. Together with the power formula P = V × I, it links the four basic quantities of a simple circuit — voltage, current, resistance and power — so that knowing any two of them fixes the other two.

Which two values do I need to enter?

Any two of the four: voltage and current, volts and ohms, watts and amps, or any other pair. The calculator solves for the remaining two. If you fill in three or four boxes, it solves from the first complete pair in this order — voltage and current, then voltage and resistance, then voltage and power, then current and resistance, then current and power, then resistance and power — so that all four results agree with each other.

How do I find watts from volts and amps?

Multiply them: P = V × I. A device drawing 2 amps from a 120-volt outlet uses 120 × 2 = 240 watts. Enter 120 in the voltage box and 2 in the current box above and the calculator shows the power — and the resistance, 60 ohms — at the same time.

Can resistance be zero?

Not in these formulas. A resistance of exactly 0 ohms would let unlimited current flow for any voltage, so the calculator asks for a resistance above 0. Real wires come close to zero resistance, which is exactly why a short circuit draws so much current and trips a breaker.

Does Ohm's law work for every circuit?

It works exactly for resistors and resistive loads — heaters, incandescent lamps, plain wire — at a steady temperature. It is only an approximation for things like LEDs, motors, batteries being charged and anything electronic, because their effective resistance changes with voltage and current. For those, treat the result as a rough guide, not a design value.

Disclaimer: Results are for education and general use. Check important calculations independently before relying on them for exams, work, or decisions where accuracy matters.