Home › Math & Science › Frustum Calculator

Frustum Calculator

A tapered bucket, flower pot or lampshade holds less than a straight cylinder but more than a cone — and guessing its capacity is nearly impossible by eye. This free frustum calculator takes the top radius, bottom radius and height and returns the volume, slant height and surface area, in metric or imperial units.

—

How it works

A frustum is a cone with its tip cut off by a slice parallel to the base. That leaves two circular faces: the bottom, with radius R, and the top, with radius r, separated by the height h. Because the wall slopes evenly from one circle to the other, a single formula captures the volume — it is, in effect, the average behavior of the two end circles blended with a cross term.

Volume V = (1/3) × π × h × (R² + R×r + r²)  ·  Slant height s = √(h² + (R − r)²)  ·  Lateral area = π × (R + r) × s

The bottom radius R and top radius r are measured from the center of each circular face to its edge. If you measured across the whole face instead, choose diameter and the tool halves the values for you. Either radius may be the larger one — a flared lampshade with a wide top works exactly like a tapered bucket. The height h is the perpendicular distance between the two faces, not the length of the sloping side; that slope length is the slant height, which the tool derives for you. Total surface area adds the two circular ends, π×R² and π×r², to the lateral area, and the liters line converts the volume using 1 liter = 1,000 cm³.

Worked example

A tapered planter has a bottom radius of 6 cm, a top radius of 4 cm and a height of 5 cm. Step 1: square and combine the radii — R² + R×r + r² = 36 + 24 + 16 = 76. Step 2: multiply by the height and by π⁄3 — (1/3) × π × 5 × 76 = 397.94 cm³ of soil, about 0.398 liters. The slant height is √(5² + (6 − 4)²) = √29 = 5.39 cm, and the side area is π × (6 + 4) × 5.39 = 169.19 cm². Enter bottom radius 6, top radius 4, height 5 above and the calculator shows the same figures.

Tips for measuring real frustums

For containers, measure inside dimensions if you want capacity: bucket walls and pot rims are thick enough to matter. For a shape that continues to a point below the base — some hoppers and funnels — model the full cone and the missing tip as two frustum-style calculations and subtract, or use the cone volume formula on each part. And remember the radii enter the formula squared, so a tape-measure error of half a centimeter on a small pot shifts the answer far more than the same error on the height.

FAQ

What is a frustum?

A frustum is what is left of a cone when the tip is sliced off by a cut parallel to the base. It has two circular faces of different sizes — a larger bottom radius R and a smaller top radius r — joined by a sloping side. Buckets, flower pots, lampshades, coffee cups and tapered tanks are all frustums, which is why the shape comes up so often in real projects.

How do you calculate the volume of a frustum?

Use V = (1/3) × π × h × (R² + R×r + r²), where R is the bottom radius, r is the top radius and h is the height between the two faces. For a frustum with R = 6 cm, r = 4 cm and h = 5 cm: (1/3) × π × 5 × (36 + 24 + 16) = (1/3) × π × 5 × 76 = 397.94 cm³. The middle term R×r is what most people forget — leaving it out understates the volume.

What happens if the top radius is zero?

The frustum becomes an ordinary cone, and the formula proves it: with r = 0 the bracket (R² + R×r + r²) shrinks to just R², leaving V = (1/3) × π × h × R², which is exactly the cone volume formula. This calculator accepts a top radius of 0, so it doubles as a cone calculator when you need one.

How is the slant height of a frustum found?

The slant height is the distance measured along the sloping side, and it comes from Pythagoras: s = √(h² + (R − r)²). Only the difference between the radii matters, because the slope leans inward by exactly R − r over the height h. For R = 6, r = 4 and h = 5, s = √(25 + 4) = √29 = 5.39. The slant height is what you need to cut material for the side, and it feeds the lateral surface area π × (R + r) × s.

How do I measure a real bucket or pot as a frustum?

Measure the diameter across the bottom inside, the diameter across the top inside, and the inside depth. Choose diameter above and enter those numbers directly — the tool halves them. Using inside measurements matters: wall thickness counted in an outside diameter inflates both radii, and because volume depends on the squares of the radii, a small measuring error grows. For the example shape above, an extra 0.5 cm on each radius would overstate the volume by roughly 15%.

Disclaimer: Results assume a perfect cone frustum with flat, parallel circular faces and are estimates for planning. Real containers vary with wall thickness, rims and rounded corners — measure inside dimensions for true capacity.