Home › Math & Science › Cone Volume Calculator
Cone Volume Calculator
Party hats, traffic cones, funnels, hopper bins, piles of gravel — cones show up everywhere, and their volume is always a third of what the same-sized cylinder would hold. This free cone volume calculator takes the radius (or diameter) and height and returns the volume, the slant height, and the surface areas, in metric or imperial units, with capacity in liters.
How it works
A cone is a circle pulled up to a point. Its volume is the base circle's area stretched through the height — but because the sides taper to nothing, only a third of that space is actually filled: a cone holds exactly one third of the cylinder that shares its base and height. The slant height comes from the Pythagorean theorem applied to the radius and the upright height, and it unlocks the curved surface area.
The radius is half the diameter of the base circle — the number you get measuring straight across the bottom. The height is the vertical distance from the center of the base to the tip, not the length of the sloping side; that slope is the slant height, which the tool works out for you. Every measurement must share one unit, so the unit selector applies to all inputs at once, and the liters line converts the finished volume (1 liter = 1,000 cm³; a cubic foot is 28.3168 liters).
Worked example
A paper party hat has a base radius of 3 inches and stands 7 inches tall, and you want to know how much candy it holds. Step 1: square the radius — 3² = 9. Step 2: multiply by π — the base covers 28.27 in². Step 3: multiply by the height and take a third — 28.2743 × 7 ÷ 3 = 65.97 in³. The slant height is √(3² + 7²) = √58 ≈ 7.62 inches, and the curved side covers π × 3 × 7.6158 ≈ 71.78 in². Enter radius 3, height 7, unit in above and the calculator shows the same figures.
Tips for measuring real cones
Height is the measurement people get wrong: hold a ruler vertically from the table to the tip rather than laying it along the slope, because the formula wants the upright height. For a pile of sand or gravel, the base diameter is easy to walk off, and the angle of the pile is set by the material — sand settles near 34 degrees — so a quick sanity check is that the height should come out close to a third of the base width. For anything you will fill, remember the brim is not the working volume; a hopper or funnel filled to the lip holds a little less than the perfect-cone figure once material settles.
FAQ
How do you calculate the volume of a cone?
Multiply the area of the circular base by the height, then take a third of it: V = (1/3) × π × r² × h. A cone with radius 3 and height 7 has a base area of π × 9 = 28.27, so its volume is 28.27 × 7 ÷ 3 = 65.97. A cone always holds exactly one third of the cylinder with the same base and height.
What is the slant height of a cone and why does it matter?
The slant height is the distance from the tip down the sloping side to the edge of the base: l = √(r² + h²). For radius 3 and height 7 it is √58 = 7.62. You need it for the lateral surface area — the curved side you would paint, wrap or cut from sheet material — which is π × r × l.
What if I only know the diameter of the base?
Halve it to get the radius, or choose diameter in this calculator and enter the base width directly. A cone with a 6-inch base has radius 3 inches, so with a height of 7 inches its volume is the same 65.97 cubic inches as the radius example.
How is a cone different from a pyramid in volume?
The rule is the same — one third of base area times height — only the base area changes. A cone uses the circle area π × r²; a pyramid uses the area of its square or polygonal base. If you remember the one-third rule, you can get the volume of either shape from its base and height alone.
Can I use this for a cone that is cut off at the top?
Not directly. A cut-off cone is a frustum, and it needs its own formula using both the top and bottom radii. A quick estimate is to calculate the full cone, then subtract the small cone that was removed from the tip — this calculator handles each of those two cones separately if you know their heights.