Home › Home & Construction › Fish Tank Calculator
Fish Tank Calculator
A tank's sticker size and its real water volume are rarely the same number, and the difference decides your filter, your heater, your dosing — and whether the floor is happy. This free fish tank calculator turns three measurements into the true volume in gallons and liters, the filled weight, and sensible filter and heater sizes.
Most tanks are filled to 90–95% rather than the rim — set the level you will actually run.
| Water volume (US gallons) | — |
| Water volume (liters) | — |
| Weight of the water | — |
| Filter flow to aim for (4–6× per hour) | — |
| Heater guide (3–5 W per gallon) | — |
How it works
The calculator measures the water, not the marketing. Manufacturers quote a tank's nominal size from its outside dimensions filled to the brim; your fish live in the inside volume at your real water line, with gravel and rock displacing some of it. Three measurements and a fill level get you the honest number everything else — dosing, flow, heating — is based on.
For a rectangular tank, volume is length × width × height. For a cylinder, enter the diameter and height and the width box disappears — a cylinder has no separate width. Measure inside the glass where you can: thick acrylic or glass on a big tank can shave several percent off the outside-dimension volume. The fill level then scales the volume to the water line you actually keep — substrate displacement is roughly handled by the same percentage if yours sits a little low.
The equipment figures are guides drawn from the volume. Filter flow at 4–6 tank volumes per hour is the widely used range for a healthy freshwater setup — planted and lightly stocked tanks sit at the low end, messy fish at the high end. Heater watts at 3–5 watts per gallon cover most tropical tanks in a heated home; unheated rooms and large tanks argue for the top of the range. The weight shown is the water alone — add the empty tank, substrate, rock and stand contents before you judge a floor or a stand.
Worked example
The classic 50-gallon breeder footprint: 36 inches long, 18 wide, 18 high, filled to the top. Step 1: volume in cubic inches is 36 × 18 × 18 = 11,664. Step 2: gallons are 11,664 ÷ 231 = 50.5 US gallons. Step 3: in liters, 11,664 cubic inches is 191.1 liters. Step 4: the water weighs 50.5 × 8.34 = about 421 lb — before the tank, gravel and stand. Step 5: the filter should move 4–6 times the volume per hour, so roughly 202–303 gallons per hour, and the heater guide is 3–5 watts per gallon, about 151–252 watts — one 200 W heater or a pair of smaller ones. Those are the numbers the calculator shows for the default inputs; drop the fill level to 90% and every figure scales down honestly with the water.
Before the tank goes on the stand
Weight is a floor question, not a furniture question. Water alone in a 75-gallon tank weighs about 626 lb. Add glass, substrate and rock and a big setup can pass 800–900 lb concentrated on four small feet. Place large tanks across floor joists, ideally against a load-bearing wall, and level the stand — an unlevel tank stresses its seams.
Nominal sizes lie kindly. A "20-gallon" tank filled to a working level with two inches of gravel may hold 16–17 gallons of water. Dose medication and fertilizer to the real volume from this calculator, not the box.
Oversize the filter, not the stocking. Filter ratings are usually measured empty and clean; a mature filter moves less. Buying the next size up is cheap insurance, while adding "just one more fish" spends the safety margin you just bought.
FAQ
How do I calculate how many gallons my tank holds?
For a rectangular tank, multiply length × width × height in inches and divide by 231 — there are 231 cubic inches in a US gallon. A 36 × 18 × 18 inch tank is 11,664 cubic inches, which is 11,664 ÷ 231 = 50.5 gallons. In metric, multiply the centimeter dimensions and divide by 1,000 to get liters. This calculator does both and adjusts for how full you actually fill the tank.
Why is the filled weight so much more than the water?
It isn't, in this calculator — the weight shown is the water alone, at 8.34 pounds per gallon. The glass or acrylic, gravel or sand, rocks, filter and hood all add more, commonly 10–25% on a typical setup, and the water line is rarely at the very rim. Before placing a large tank, weigh up the total honestly: a filled 75-gallon setup can pass 800 pounds, which is a question for the floor and the stand, not just the tape measure.
What size filter and heater do I need?
A common guide is a filter that turns the whole tank volume over 4 to 6 times per hour — a 50-gallon tank wants roughly 200–300 gallons per hour of flow. For heat, 3 to 5 watts per gallon suits most tropical setups in a normally heated room; a cold room or a large temperature lift needs the top of the range or two smaller heaters. This calculator shows both ranges from your actual volume.
How accurate is the cylinder calculation?
The cylinder volume uses π × radius² × height with your diameter and height, which is exact for a true cylinder. It is measured to the inside of the glass in both shapes: outside dimensions overstate the water a little, especially in thick glass or acrylic, so measure inside where you can — or knock a small percentage off and set the fill level to 95% to be realistic.
Can I use the volume to decide how many fish to keep?
Only as a starting point. How many fish a tank supports depends on the species, their adult size, how much waste they produce, filtration, plants, and how the fish behave toward each other — a volume number cannot see any of that. Research each species' needs and stock conservatively; the old inch-per-gallon rule is widely considered too crude to trust.