Home › Converters › PSI to Bar Converter

PSI to Bar Converter

Your tire gauge reads psi, but the door-jamb sticker on your European car — or the manual for your espresso machine, bike fork, or paintball tank — is printed in bar. This free psi to bar converter switches between them instantly, and it also converts kilopascals, millibars, atmospheres, mmHg, and kg/cm² in either direction, so whichever gauge you are holding, the numbers line up.

The line under the result shows the same pressure in kPa and atmospheres too — the units on most gauges and spec sheets.

2.4821 bar
36 psi = 2.4821 bar · 248.2113 kPa · 2.4497 atm

PSI to bar conversion table

Everyday pressures — tires, atmosphere, bike suspension, and shop air — converted to bar and kilopascals.

PSIBarKilopascals (kPa)

How it works

Both units measure the same thing — force spread over an area — they just start from different definitions. A psi is one pound of force on one square inch. A bar is defined metrically as exactly 100,000 pascals, and a pascal is one newton per square meter. Dividing the two definitions gives the exact bridge: 1 bar = 14.5037738 psi. This converter uses psi as its base unit, so any pair works — bar to mmHg, kPa to atm — through one shared set of factors.

PSI to bar: bar = psi ÷ 14.5037738  |  Bar to psi: psi = bar × 14.5037738  |  1 bar = 100 kPa = 1,000 mbar  |  Any pair: result = amount × (psi per from-unit) ÷ (psi per to-unit)

Because a bar is roughly fourteen and a half times bigger than a psi, bar figures always look small and psi figures look big for the same pressure. A car tire is about 2.2 bar or 32 psi; a road bike tire might be 6 bar or 87 psi; a pressure washer at 3,000 psi is a little over 200 bar. Recognizing that scale at a glance is the fastest sanity check: if your converted tire pressure comes out above 10 bar, a decimal point has gone missing.

Enter the amount, pick the from and to units, and the answer updates as you type. The line underneath restates the result and adds the same pressure in kilopascals (the unit on many digital gauges and weather instruments) and in atmospheres. Use the swap button to reverse the direction, for example when a manual gives bar and your gauge reads psi.

Worked example

Dan's hatchback was built for the European market, so the door sticker lists tire pressure as 2.5 bar, but his gas-station gauge reads psi — and his tires currently sit at 36 psi. Step 1: divide the psi by the factor — 36 ÷ 14.5037738 = 2.4821. Step 2: read the result — the tires are at 2.4821 bar, essentially the recommended 2.5 bar, so no air is needed. Step 3 (reverse check): 2.5 bar × 14.5037738 = 36.259 psi, matching what his gauge would show at the full recommended pressure.

Common mistakes

The most common mistake is treating psi and bar as if they were near each other, like inches and centimeters — they are not: over-inflating a tire to "30 bar" instead of 30 psi would be more than fourteen times the intended pressure, far beyond what the tire can hold. The second mistake is confusing gauge pressure with absolute pressure: tire gauges read relative to the surrounding air (psig), while some engineering figures are absolute (psia), which differ by about 14.7 psi — one atmosphere. This converter translates units only; it does not switch between gauge and absolute.

FAQ

How many psi are in a bar?

One bar is 14.5037738 psi — usually rounded to 14.5. So 2 bar is about 29 psi, 2.5 bar is 36.259 psi, and 3 bar is 43.511 psi. Divide psi by 14.5037738 to get bar.

What is 30 psi in bar?

30 psi is 2.0684 bar (30 ÷ 14.5037738). That is a typical passenger-car tire pressure on a European door-jamb sticker: most cars call for somewhere between 2.0 and 2.5 bar, which is 29 to 36 psi.

What is standard atmospheric pressure in psi and bar?

Standard atmospheric pressure at sea level is 14.6959 psi, which is 1.01325 bar (one standard atmosphere, 1 atm). Weather reports give the same pressure in hectopascals or millibars: 1,013.25 mbar.

Which is the bigger unit, psi or bar?

A bar is much bigger: one bar equals about 14.5 psi. That is why tire pressures read as small numbers in bar (2.0–2.5) and larger numbers in psi (29–36), while a pressure washer rated at 3,000 psi is about 206.8 bar.

How do you convert psi to bar?

Divide the psi by 14.5037738, or multiply by 0.0689476. For example, 36 psi ÷ 14.5037738 = 2.4821 bar. To convert bar back to psi, multiply by 14.5037738: 2.5 bar × 14.5037738 = 36.259 psi.

Disclaimer: Results are conversions for guidance only. Values are rounded for display; for legal, medical, or safety-critical use, confirm with an official source or a qualified professional.