Home › Converters › Carat Calculator

Carat Calculator

A jeweler can weigh a loose diamond on a scale, but a stone that is already set in a ring cannot be weighed directly — its carat weight has to be estimated from its measurements. This carat calculator does exactly that: choose the shape, enter the length, width and depth in millimeters, and it applies the standard estimation formula for that cut to give you the approximate carat weight. It is the same approach appraisers use for a first estimate on mounted stones and for checking whether a certificate matches a stone.

For a round stone, length and width are both the diameter.

1.01 ct
Round brilliant, 6.5 × 6.5 × 3.9 mm — estimated weight 1.01 carats (about 0.20 grams). Estimates vary with cut proportions.

Round diamond size guide

For round brilliants, weight tracks diameter closely when the cut proportions are typical. This guide uses the same formula as the calculator, assuming a depth of about 60% of the diameter. A deeper or shallower stone of the same diameter will weigh more or less.

DiameterEstimated weight
3.0 mm0.10 ct
4.0 mm0.23 ct
4.5 mm0.33 ct
5.0 mm0.46 ct
5.2 mm0.51 ct
5.9 mm0.75 ct
6.5 mm1.01 ct
6.9 mm1.20 ct
7.4 mm1.48 ct
8.2 mm2.02 ct
9.4 mm3.04 ct
10.0 mm3.66 ct

How it works

Diamond is a material with a fixed density, so a stone's weight is set by its volume — and volume can be estimated from three caliper measurements: length, width and depth. Each cut shape fills its bounding box differently, so each shape gets its own coefficient that converts the measured volume in cubic millimeters into carats:

Estimated carats = length × width × depth × shape coefficient  |  Round 0.0061 · Oval 0.0062 · Princess 0.0083 · Emerald 0.0080 · Pear 0.00615 · Marquise 0.00585 (measurements in mm)

Enter the shape and the three measurements in millimeters. Length and width are the stone's outline viewed from above; depth is the total height from the table (the flat top) to the culet (the bottom point). For a round stone, length and width are both simply the diameter. The result is an estimate, shown rounded to two decimal places, with the equivalent weight in grams alongside (one carat is exactly 0.2 grams).

Treat the answer as a well-informed estimate, not a weighing. The published coefficients assume typical cut proportions. A stone cut deep for its outline — with a thick girdle or a bulging pavilion — holds more volume than the formula assumes and will weigh more; a shallow, spread stone weighs less. Two stones with identical length, width and depth can still differ by several percent in true weight, which is why a scale or a full appraisal is needed for an exact figure.

Worked example

A shopper in Chicago is comparing a solitaire described as "about one carat." The listing gives the round stone's measurements as 6.5 mm across and 3.9 mm deep.

Step 1: Multiply the three measurements — 6.5 × 6.5 × 3.9 = 164.775 cubic millimeters.
Step 2: Apply the round brilliant coefficient — 164.775 × 0.0061 = 1.0051.
Step 3: Round to two decimals — 1.01 carats.

The calculator reports 1.01 ct, confirming the listing's "about one carat" claim. The same stone works out to about 0.20 grams, since a carat is 0.2 grams — a useful sanity check, because a true 1-carat round diamond of typical proportions is almost always close to 6.5 mm in diameter.

Common mistakes and tips

The biggest measuring mistake is skipping the depth. Diameter alone cannot give a weight: a deep-cut 6.5 mm round can outweigh a shallow one by 20% or more, because most of a diamond's volume sits below the girdle where you cannot see it in a setting. If you can only measure the diameter of a set stone, use the size guide above and treat the answer as a rough range, not a number.

Measure carefully with calipers rather than a ruler — a half-millimeter error on a small stone changes the estimate noticeably, since all three dimensions multiply together. And remember that these coefficients are calibrated for diamond's density. The same measurements on a sapphire, moissanite or cubic zirconia give a different true weight, because each material's density differs; the estimate will be in the right neighborhood but should not be quoted as that gem's weight.

FAQ

How accurate is a carat estimate from measurements?

For a stone with typical cut proportions, the standard formulas usually land within a few percent of the true weight. Stones cut unusually deep or shallow can be off by 10% or more, because the formulas assume average proportions. Only a scale gives an exact weight, and a set stone cannot be weighed directly.

What is the formula for a round diamond's carat weight?

For a round brilliant, estimated carats = diameter × diameter × depth × 0.0061, with all measurements in millimeters. A 6.5 × 6.5 × 3.9 mm stone gives 6.5 × 6.5 × 3.9 × 0.0061 = 1.01 carats, which is the classic one-carat size.

How many millimeters is a 1 carat round diamond?

A well-cut 1 carat round brilliant is about 6.5 mm in diameter. Smaller rounds follow the same curve: roughly 5.2 mm is half a carat, 7.4 mm is about 1.5 carats, and 8.2 mm is about 2 carats, as the size guide above shows.

Why do two stones with the same measurements weigh differently?

Because the formulas assume typical proportions. A thick girdle, a deep pavilion or a high crown adds volume — and therefore weight — that the three headline measurements do not fully capture. Cut quality is the main reason a measurement-based estimate is a range, not an exact figure.

Can I use this calculator for other gemstones?

The coefficients are calibrated for diamond, which has a specific density of about 3.52. Other gems have different densities — sapphire is denser, for example — so the same measurements give a different true weight. The result is a rough guide for other stones, not a reliable weight.

Disclaimer: Results are conversions for guidance only. Values are rounded for display; for legal, medical, or safety-critical use, confirm with an official source or a qualified professional.