Home › Math & Science › Torque Calculator

Torque Calculator

Twisting force hides a third ingredient most quick calculations forget: the angle of the push. This free torque calculator solves τ = F × r × sinθ for torque, force or lever distance, with force in newtons, pounds-force or kilograms-force, distance in meters, centimeters, feet or inches, and the angle in degrees — and reports torque in both N·m and lbf·ft.

Torque = 50 N·m
τ = 100 N × 0.5 m × sin(90°) · also 36.8781 lbf·ft
Torque50 N·m · 36.8781 lbf·ft
Force100 N · 22.4809 lbf
Lever distance0.5 m · 1.6404 ft
Angle90° · sin = 1

How it works

Torque is the rotational version of force: not just how hard you push, but where you push and in which direction. A door opens easily when you press far from the hinge and barely budges when you press next to it — same force, wildly different torque.

τ = F × r × sinθ   •   F = τ ÷ (r × sinθ)   •   r = τ ÷ (F × sinθ)

The force (F) is the push or pull, entered in newtons, pounds-force or kilograms-force and converted to newtons internally (1 lbf = 4.44822 N; 1 kgf = 9.80665 N). The lever distance (r) runs from the pivot to the line where the force lands, in meters, centimeters, feet or inches. The angle (θ) sits between the force and the arm: 90° means a clean perpendicular push and is the default for a reason. The sine of the angle is the share of the force that actually rotates — all of it at 90°, about 71% at 45°, and none at 0°, when you are pushing straight into the pivot.

This is why a longer wrench loosens the bolt a short one cannot: doubling r doubles τ without any extra effort. It is also why mechanics choke up on a wrench for delicate fasteners — halving the arm halves the torque your hand applies, which is cheaper than a snapped bolt.

Worked example

A mechanic pulls a wrench with 100 N of force at the end of a 0.5 m handle, square-on to the bolt. How much torque reaches the bolt?

Step 1 — write the formula: τ = F × r × sinθ.
Step 2 — substitute: τ = 100 × 0.5 × sin(90°).
Step 3 — sin(90°) is 1, so τ = 100 × 0.5 = 50 N·m, which is 36.88 lbf·ft.

Those defaults are loaded in the calculator above. Now change only the angle to 45° and watch the torque fall to 35.36 N·m — same pull, same wrench, a quarter of the turning effect lost to a sloppy angle. The reverse modes check against the same numbers: solving for force from 50 N·m at 0.5 m and 90° returns exactly 100 N.

Common mistakes

Ignoring the angle. Most back-of-envelope torque math silently assumes 90°. On a real bolt the wrench is often pulled at whatever angle the engine bay allows, and at 30° the true torque is only half of F × r. If the number matters, the angle matters.

Confusing lbf·ft with ft·lbf energy. Torque specs are written in pound-feet; the number is a twisting force, not work done. Keep it in N·m or lbf·ft and resist calling it joules — no rotation has happened yet.

Measuring the arm from the wrong point. The lever distance runs from the pivot (the bolt's center) to where the force is applied — the full handle length only if you pull at the very end. Gripping halfway down a 0.5 m wrench gives you a 0.25 m arm and half the torque.

FAQ

What is the torque formula?

Torque is τ = F × r × sinθ: the force, times the lever-arm distance from the pivot, times the sine of the angle between them. A 100 N push at 0.5 m, applied at a right angle, gives 100 × 0.5 × 1 = 50 N·m. Only the part of the force that acts perpendicular to the arm turns anything — that is what the sinθ term accounts for.

Why does the angle of the force matter?

Pushing straight along the wrench toward the bolt (0°) turns nothing at all, however hard you push, because none of the force acts to rotate. Pushing at 90° puts the whole force into rotation. At 45° you get sin45 ≈ 0.707 of the full effect. That is why you instinctively pull a wrench handle at a right angle — and why slipping to a shallow angle on a tight bolt feels so futile.

How do newton-meters and pound-feet convert?

1 lbf·ft = 1.35582 N·m, and 1 N·m = 0.73756 lbf·ft. So 50 N·m is 36.88 lbf·ft, and a wheel-nut spec of 100 lbf·ft is 135.58 N·m. US torque wrenches are usually marked in lbf·ft (or lbf·in for small fasteners) and metric ones in N·m — this calculator reports both so a spec in either system can be checked.

Is torque the same as energy?

No, although they share the unit name newton-meter. Energy (work) is force times the distance moved along the force's direction. Torque is force times the lever distance at right angles to the force, and nothing has moved yet. Physicists keep them apart by writing energy in joules and leaving torque in plain N·m — same dimensions, different physical idea.

How is engine torque different from horsepower?

Torque is the twisting force itself; power is torque multiplied by how fast the shaft spins. An engine making 300 N·m at 4,000 rpm produces about 125.7 kW (300 × 4,000 × 2π ÷ 60 ÷ 1,000). A high-torque engine that cannot rev may make less power than a modest-torque engine that spins freely — which is why both numbers appear on a spec sheet.

Disclaimer: Results are for education and general use. Check important calculations independently before relying on them for exams, work, or decisions where accuracy matters.