Home › Home & Construction › Driveway Calculator

Driveway Calculator

Order too little gravel and the truck has gone home before you find the thin patch; order too much concrete and you are paying to dump the surplus. This free driveway calculator takes the length, width and depth of your drive and works out the material in the unit it is actually sold in — tons for gravel and asphalt, cubic yards for concrete — with an optional cost at your local price.

The currency only changes the symbol and formatting — it never converts amounts. Leave the price blank to skip the cost.

3.46 tons of gravel
Volume 66.67 cu ft · 2.4691 cu yd · no waste allowance · cost —
Driveway volume66.67 cu ft · 2.4691 cu yd
Material needed (exact)3.4568 tons
Order quantity (with allowance)3.46 tons
Estimated cost—

How it works

Every driveway material starts from the same volume — length times width times depth — but each trade sells in a different unit, so the calculator converts volume into the unit your supplier quotes. Gravel and asphalt are weighed, concrete is batched by volume.

Volume (cu ft) = length × width × (depth ÷ 12)   •   Cubic yards = cu ft ÷ 27   •   Gravel tons = cu yd × 1.4   •   Asphalt tons = cu ft × 145 lb ÷ 2,000

The gravel factor of 1.4 tons per cubic yard is the middle of the range suppliers use for driveway stone (roughly 1.35–1.5 depending on the stone and how wet it is); your quarry's yield figure wins if they publish one. Asphalt at 145 lb per cubic foot is the standard compacted density for hot mix. Concrete needs no density at all — ready-mix is ordered in cubic yards, and a 4-inch slab is the usual driveway pour. The waste allowance multiplies the finished quantity, not the volume, so the “order quantity” line is the number to say to the supplier.

Worked example

A single-car gravel driveway, 20 ft long × 10 ft wide, topped up 4 inches deep, with no waste allowance.

Step 1 — volume: 20 × 10 × (4 ÷ 12) = 66.67 cu ft.
Step 2 — cubic yards: 66.67 ÷ 27 = 2.4691 cu yd.
Step 3 — gravel weight: 2.4691 × 1.4 = 3.4568 tons, so 3.46 tons of gravel.

Enter the same numbers above and the result matches. Set the waste allowance to 10% and the order quantity becomes 3.80 tons — the amount to actually order once settling and spillage are covered. At $45 a ton, that order would cost $171.11.

Getting the order right

Measure the depth you are adding, not the depth you wish you had. An existing gravel drive that looks 4 inches deep is often 2 inches over a compacted base; the new material only needs to cover the top-up depth.

Depth drives everything. Because volume is linear in depth, a 6-inch spec costs exactly half again as much as a 4-inch spec. If the budget is tight, it is usually better to keep the full depth on the parking area and accept a thinner layer on a little-used spur.

Confirm the supplier's unit before you quote the number. Some landscape yards sell gravel by the cubic yard (a “scoop”) rather than the ton; this calculator shows both volume figures in the result table so you can order either way.

FAQ

How many tons of gravel do I need for a 20 × 10 driveway?

At 4 inches deep, a 20 × 10 ft driveway is 66.67 cubic feet — 2.47 cubic yards. Gravel weighs about 1.4 tons per cubic yard once spread, so you need 2.47 × 1.4 = 3.46 tons. Add a 10% waste allowance and order about 3.8 tons, because gravel settles into the base and a load spread slightly thin in one corner is hard to fix after the truck leaves.

How deep should a gravel driveway be?

A common build-up is 4 inches of coarse base stone, then 3–4 inches of finer surface gravel — but for a single-layer top-up of an existing drive, 3–4 inches of new material is typical. This calculator works per layer: run it once for each layer at its own depth and add the tonnages. Depth is the biggest lever in the result — going from 3 to 4 inches adds a full third to the order.

How is asphalt measured, and why tons instead of yards?

Asphalt plants sell hot mix by the ton, and compacted asphalt weighs about 145 lb per cubic foot, so the calculator converts your driveway's volume straight to tons: a 20 × 10 ft drive at 3 inches is 50 cubic feet, which is 50 × 145 ÷ 2,000 = 3.63 tons. Quote the tonnage to the plant and confirm their yield figure, because mixes vary a little in density.

Should I order extra material?

Yes — uneven ground, spillage, compaction and edges that are not perfectly square all eat material. Five percent is the minimum sensible allowance and 10% is standard for gravel and DIY concrete work; use the waste selector rather than doing the math in your head, because the allowance is applied to the final order quantity, not the raw volume, in the result table.

Can I use this for a concrete driveway slab?

Yes — choose concrete and it reports cubic yards, the unit ready-mix trucks sell by. A residential concrete driveway is usually poured 4 inches thick (5–6 inches where heavy trucks park), often over a compacted gravel base you can size by running the calculator again with gravel selected. Remember the result is the neat in-place volume; the waste allowance is what covers formwork bulge and the last partial yard.

Disclaimer: Quantities are estimates using 1.4 tons per cubic yard for gravel and 145 lb per cubic foot for compacted asphalt. Actual yields vary with material, moisture and compaction — confirm the yield with your supplier before ordering, and check local rules for driveway permits and drainage.