Home › Health, Fitness & Education › Squat Calculator
Squat Calculator
You know what you squatted for five reps — but your program asks for 85% of your one-rep max, and testing a true max is a production. This free squat calculator estimates your 1RM from any set using both the Epley and Brzycki formulas, lays out working weights from 95% down to 65%, and, if you add your bodyweight, places the result against common strength-level benchmarks.
| % of 1RM | Working weight | Typical reps |
|---|---|---|
| 95% | 108.9 kg | about 2 |
| 90% | 103.1 kg | about 3–4 |
| 85% | 97.4 kg | about 5–6 |
| 80% | 91.7 kg | about 7–8 |
| 75% | 85.9 kg | about 9–10 |
| 70% | 80.2 kg | about 11–12 |
| 65% | 74.5 kg | about 14–15 |
How it works
A one-rep max is the heaviest weight you can squat once with good form. Testing it directly is slow and risky, so coaches estimate it from a hard submaximal set instead — the heavier the set relative to the weight and the fewer the reps, the more the estimate can be trusted.
The weight lifted is the total on the bar, bar included, in kilograms or pounds. The reps are the full, good-form repetitions you completed — ideally a set taken close to failure, since a set you stopped early understates your strength. The calculator runs both classic formulas: Epley tends to read a touch high, Brzycki a touch conservative, so the headline number is their average, with both shown so you can see the spread. At exactly 1 rep, the estimate is simply the weight you lifted. Working weights in the table are percentages of that average 1RM, paired with the reps a typical lifter manages at each level.
The optional bodyweight powers the strength-level note. It compares your estimated 1RM to common gym benchmarks for your bodyweight ratio — informal reference bands gathered from lifting practice, not official federation standards. Leave it blank and everything else still works.
Worked example
A lifter squats 100 kg for 5 solid reps and wants training weights for the month ahead.
Step 1 — Epley: 100 × (1 + 5 ÷ 30) = 100 × 1.1667 = 116.7 kg.
Step 2 — Brzycki: 100 × 36 ÷ (37 − 5) = 3,600 ÷ 32 = 112.5 kg.
Step 3 — average: (116.7 + 112.5) ÷ 2 = 114.6 kg estimated 1RM.
Step 4 — a heavy day at 85%: 0.85 × 114.6 = 97.4 kg, loaded as 97.5 kg with standard plates.
Those are the figures pre-loaded above. If the same lifter weighs 80 kg, the ratio is 114.6 ÷ 80 ≈ 1.43× bodyweight — just under the 1.5× intermediate benchmark for men, which is the note the calculator adds when bodyweight is entered.
Common mistakes
Estimating from a set that was not hard. Both formulas assume the set ended near your limit. Five easy reps stopped early might correspond to a much heavier true set, and the estimate will undershoot.
Trusting high-rep estimates. A set of 15 measures endurance as much as strength; the formulas can overshoot by several percent there. A heavy set of 3–5 is the sweet spot for an honest number.
Forgetting the bar. An Olympic bar is 20 kg (45 lb). Entering only the plates understates the weight by the whole bar — on a 100 kg squat, that is a fifth of the lift.
FAQ
How is a squat one-rep max estimated?
Two well-known formulas turn a set into a one-rep max estimate. Epley: 1RM = weight × (1 + reps ÷ 30). Brzycki: 1RM = weight × 36 ÷ (37 − reps). For 100 kg × 5 reps they give 116.7 kg and 112.5 kg. This calculator shows both and headlines their average, 114.6 kg — a sensible middle estimate rather than either formula's opinion alone.
How accurate are 1RM estimates?
Reasonably close for sets of 2–10 hard reps, and shakier beyond that — at 15 reps the formulas can overshoot by several percent because endurance starts to matter more than strength. Estimates also assume the set was taken close to failure with good form. Treat the number as a planning guide for picking training weights, not as a tested max.
Should I test a true one-rep max instead?
Only with care: a true max attempt needs a warm-up progression, a spotter or safety arms set at the right height, and good depth and form under a load you have never lifted. Most lifters get everything they need from a heavy set of 3–5 reps and an estimate like this one, at a fraction of the risk. Never test a max alone in a rack without safeties.
What is a good squat for my bodyweight?
Common gym benchmarks for men put a squat 1RM at about 0.75× bodyweight for untrained, 1.25× for novice, 1.5× for intermediate, 2.0× for advanced and 2.5× for elite; for women roughly 0.5×, 0.85×, 1.15×, 1.5× and 1.95×. These are informal reference points gathered from gym practice, not official standards — body proportions, training history and depth all move them.
How do I use the percentage table?
Pick the row whose percentage matches your program for the day: a heavy strength day might use 85% for sets of about 5–6, while volume work sits near 70% for sets of 11–12. The weights in the table are percentages of the estimated 1RM shown at the top. Round to the plates you actually have — being 1 kg off the paper number changes nothing.