Home › Converters › RPM to Hz
RPM to Hz
A motor nameplate, a vibration reading, or a datasheet gives you a speed in revolutions per minute, but the formula, the test equipment, or the specification in front of you works in hertz. This rpm to hz converter bridges the two instantly — divide by 60 under the hood — and also converts kilohertz, megahertz, gigahertz, radians per second and degrees per second, with a full breakdown of every equivalent.
RPM to Hz conversion table
| RPM | Hertz (Hz) | Radians per second | Typical source |
|---|---|---|---|
| 60 | 1 | 6.28319 | One turn per second |
| 300 | 5 | 31.41593 | Slow ceiling fan |
| 900 | 15 | 94.24778 | Idling car engine (approx.) |
| 1,800 | 30 | 188.49556 | Four-pole motor on 60 Hz power |
| 3,000 | 50 | 314.15927 | Two-pole motor on 50 Hz power |
| 3,600 | 60 | 376.99112 | Two-pole motor on 60 Hz power |
| 5,400 | 90 | 565.48668 | Older hard disk drive |
| 7,200 | 120 | 753.98224 | Desktop hard disk drive |
| 10,000 | 166.66667 | 1,047.19755 | High-speed spindle |
How it works
RPM and Hz count the same thing — how often a cycle repeats — in different time windows. RPM counts revolutions in one minute; hertz counts cycles in one second. Since a minute holds 60 seconds, the whole conversion is a single division: a shaft that turns 1,800 times in a minute turns 1,800 ÷ 60 = 30 times in each second, and "30 times per second" is precisely what 30 Hz means. One revolution per second is both 60 RPM and 1 Hz, and the two scales are locked together by that factor of 60.
The wider unit list covers the places frequency shows up beyond spinning shafts. Kilohertz, megahertz and gigahertz are the hertz scaled by thousands, millions and billions — the territory of radio, processors and wireless signals. Radians per second is the angular velocity engineers use in equations: one full revolution is 2π radians, so Hz × 2π gives rad/s. Degrees per second does the same job in plain geometry at 360 degrees per revolution. Everything on this page runs through hertz under the hood, so any pair you pick agrees with every other.
Worked example
An HVAC technician in Texas is checking a blower motor rated at 1,800 RPM. The vibration app on his phone reports dominant frequency in hertz, and he wants the number the healthy motor should show.
Step 1: Write down the speed — 1,800 RPM.
Step 2: Use the factor — Hz = RPM ÷ 60.
Step 3: Divide: 1,800 ÷ 60 = 30.
Step 4: Read the result — 30 Hz.
The converter gives exactly 30 Hz, and the breakdown adds 188.49556 radians per second for the engineering view. A healthy blower should peak right at that 30 Hz line; a strong reading at 60 Hz instead would point at twice-per-revolution trouble, such as misalignment — which is why converting the nameplate speed before diagnosing saves guesswork.
Common mistakes and tips
The classic slip is multiplying by 60 instead of dividing — sanity-check with the anchor: 60 RPM is 1 Hz, so any RPM figure must shrink when it becomes hertz. The second mistake is treating a motor's electrical frequency as its shaft speed without counting poles: a four-pole motor on 60 Hz mains turns at 1,800 RPM, not 3,600, because it advances half a revolution per cycle. Slip makes real induction motors run a few percent under the synchronous figure, so a nameplate 1,760 RPM (29.33333 Hz) is normal, not a fault. Finally, a record player at 33⅓ RPM spins at about 0.55556 Hz — a reminder that hertz below 1 are perfectly ordinary for slow machinery.
FAQ
How do you convert RPM to Hz?
Divide the RPM by 60. RPM counts revolutions per minute and Hz counts cycles per second, so Hz = RPM ÷ 60. A shaft turning at 1,800 RPM completes 1,800 ÷ 60 = 30 revolutions every second, which is 30 Hz.
What is 60 RPM in Hz?
60 RPM is exactly 1 Hz — one revolution per second. That is the reference point of the whole conversion: the second hand of a clock turns at 1 RPM, which is one sixtieth of that, about 0.01667 Hz.
What is 3600 RPM in Hz?
3,600 RPM is 60 Hz (3,600 ÷ 60 = 60). That is why the number feels familiar: North American mains electricity alternates at 60 Hz, and a two-pole motor fed by it spins at a synchronous 3,600 RPM.
How do I convert Hz back to RPM?
Multiply the hertz by 60: RPM = Hz × 60. A 50 Hz vibration is 50 × 60 = 3,000 RPM, and the 60 Hz hum of mains power is 3,600 cycles per minute. The Swap button on this converter reverses the units in one click.
What is the difference between RPM and Hz?
Both measure how often something repeats. RPM (revolutions per minute) is the natural unit for rotating machinery — motors, fans, turntables. Hz (hertz) counts cycles per second and is the standard unit for waves, sound, vibration and electrical frequency. They differ only by the factor 60.