Home › Converters › GB to Bits

GB to Bits

A hard drive is advertised in gigabytes, a fiber plan in gigabits per second, and a cloud bill in a mixture of both — comparing any two of them means converting between bytes and bits. This GB to bits converter does the translation exactly: enter gigabytes (or bytes, kilobytes, megabytes or terabytes) and get the bit count in the decimal system used by manufacturers and the binary system your operating system reports, side by side. It is the quickest way to sanity-check a download time, a data cap or a bandwidth figure.

The result also shows the same data measured in the other system, underneath.

16,000,000,000 bits
2 GB = 16,000,000,000 bits (decimal) · The same data is 1.862645 GiB in binary units · Total: 16,000,000,000 bits

GB to bits conversion table

Common gigabyte amounts converted to bits in both unit systems. The binary column counts the same gigabytes the way Windows measures them, in gibibytes.

GigabytesBits (decimal)Bits (binary)

How it works

Every file size is built up from bits. A bit is a single 0 or 1; eight bits make a byte; and from there the units climb by a fixed step — 1,000 in the decimal (SI) system or 1,024 in the binary (IEC) system. A decimal gigabyte is 1,000,000,000 bytes, so converting GB to bits means multiplying by 1,000,000,000 and then by 8: one GB is exactly 8,000,000,000 bits. A binary gibibyte is 1,073,741,824 bytes, so one GiB is 8,589,934,592 bits.

GB to bits (decimal): bits = GB × 8,000,000,000  |  GiB to bits (binary): bits = GiB × 8,589,934,592  |  Any pair: result = amount × (bits per from-unit) ÷ (bits per to-unit), with steps of 1,000 (decimal) or 1,024 (binary)

Use the system that matches your source. Drive and SSD makers, download sites and internet providers count in decimal; Windows and RAM specs count in binary, which is why a drive sold as 1 TB appears as about 931 GiB on a PC. This converter defaults to gigabytes to bits, but all six units — bits, bytes, KB, MB, GB and TB — are available on both menus, and the swap button reverses the direction, so a bit rate from a network spec can also be turned back into gigabytes.

Worked example

A systems administrator in Phoenix is estimating how long a 2 GB backup image takes to move over a 100 Mbps link.

Step 1: Convert the image to bits — 2 GB × 8,000,000,000 = 16,000,000,000 bits, exactly what the converter shows.
Step 2: Put that in the link's unit — 16,000,000,000 bits is 16,000 megabits, or 16 gigabits.
Step 3: Divide by the rate — 16,000 megabits ÷ 100 megabits per second = 160 seconds, about 2 minutes 40 seconds at full speed.

Real transfers run slower once protocol overhead arrives, but the estimate starts from the right number of bits — and the binary figure is there too (the same backup is 1.862645 GiB), for comparing against what Windows reports during the copy.

Common mistakes and tips

The classic error is reading GB as Gb. The capital B is bytes and the lowercase b is bits — an eightfold difference. A "10 Gb" network diagram and a "10 GB" file are not the same quantity: the file holds 80 gigabits of data. Cloud storage adds a second trap, because providers mix systems: quotas and egress bills are usually decimal, while the operating system moving the data thinks in binary. When a transfer looks about 7% larger than expected at the gigabyte scale, that gap is the two systems, not lost data.

A handy shortcut for estimates: at the gigabyte level, the binary figure is roughly 7.4% bigger in bits than the decimal figure for the same labeled size, and the difference grows to about 10% at terabytes. For exact work — billing, caps, SLAs — convert in the system your provider uses, and keep this page's two columns side by side so the other system is never a surprise.

FAQ

How many bits are in a gigabyte?

In decimal units, one gigabyte is 8,000,000,000 bits: a gigabyte is 1,000,000,000 bytes and each byte holds 8 bits. In binary units, one gibibyte (GiB) is 8,589,934,592 bits, because a gibibyte is 1,073,741,824 bytes.

How many bits are in 2 GB?

2 GB is 16,000,000,000 bits in decimal units (2 × 8,000,000,000). The same 2 GB of data equals 1.862645 GiB in binary units, and 2 GiB would be 17,179,869,184 bits.

What is the difference between GB and Gb?

GB with a capital B is gigabytes (bytes); Gb with a lowercase b is gigabits (bits). Since a byte is 8 bits, 1 GB equals 8 Gb. Storage is sold in GB while network speeds are quoted in Gb or Gbps, so converting between them is an everyday calculation.

Why does my 1 TB drive show only about 931 GB?

Because the two numbers use different systems. The maker counts 1 TB as 1,000,000,000,000 bytes (decimal). Windows divides by 1,073,741,824 (binary) and gets about 931 GiB — it just labels the result GB. No space is missing; the units differ by about 7.4%.

Should I use decimal or binary units?

Use decimal units for manufacturer specs, internet plans, download sizes and cloud bills. Use binary units when the number came from Windows or a memory specification. When a figure really matters, check both columns — this converter shows the other system in the line under every result.

Disclaimer: Results are conversions for guidance only. Values are rounded for display; for legal, medical, or safety-critical use, confirm with an official source or a qualified professional.